How to Turn STIX On (PDOR) - Revision history

Daniel.ryan at 14:58, 4 November 2022

2022-11-04T14:58:46Z

Daniel.ryan at 14:57, 4 November 2022

2022-11-04T14:57:48Z

Daniel.ryan at 14:53, 4 November 2022

2022-11-04T14:53:55Z

Daniel.ryan at 14:45, 4 November 2022

2022-11-04T14:45:10Z

Daniel.ryan: Created page with "If STIX has been turned off, e.g. because of an issue on the satellite, we need create a PDOR to turn it back on. ==Generating a PDOR== * Open STIX-Starlet * In top toolb..."

2022-11-04T14:38:58Z

Created page with "If STIX has been turned off, e.g. because of an issue on the satellite, we need create a PDOR to turn it back on. ==Generating a PDOR== * Open STIX-Starlet * In top toolb..."

New page

If STIX has been turned off, e.g. because of an issue on the satellite, we need create a PDOR to turn it back on.

==Generating a PDOR==
* Open [[STIX-Starlet]]
* In top toolbar, click Request -> New Request
* Click Request -> PDOR (under Mode)
* Set start and end time
* Enter telecommand sequences (recommended) by clicking the Add Sequence button
* Alternatively enter individual telecommands by clicking the Add Telecommand button

@@ Line 2: / Line 2: @@
 ==Telecommands for Turning STIX On==
-Below are the telecommand sequences that must be included in the PDOR to turn STIX on.  The wait times before the next sequence is also giving.  These wait time must be adhered to or the execution of the sequennces could be interrupted. Extra things can be done as part of the PDOR, e.g. changing onboard parameters.  But this is the minimal list.
+Below are the telecommand sequences that must be included in the PDOR to turn STIX on.  The wait times before the next sequence is also given.  These wait time must be adhered to or the execution of the sequennces could be interrupted. Extra things can be done as part of the PDOR, e.g. changing onboard parameters, but this is the minimal list.
 * AIXF011. Wait time: 30 mins  (Turns STIX on and puts it into Safe mode)
 * AIXF032A.  Wait time: 1 minute (Switches from safe to nominal mode)
 * AIXF400A. Wait time: a few seconds (Enables calibration accumulation)

@@ Line 2: / Line 2: @@
 ==Telecommands for Turning STIX On==
-Below are the telecommand sequences that must be included in the PDOR to turn STIX on.  Extra things can be done as part of the PDOR, e.g. changing onboard parameters.  But this is the minimal list.
+Below are the telecommand sequences that must be included in the PDOR to turn STIX on.  The wait times before the next sequence is also giving.  These wait time must be adhered to or the execution of the sequennces could be interrupted. Extra things can be done as part of the PDOR, e.g. changing onboard parameters.  But this is the minimal list.
-* AIXF011A (Turns STIX on and puts it into Safe mode)
+* AIXF011. Wait time: 30 mins  (Turns STIX on and puts it into Safe mode)
-* AIXF032A (Switches from safe to nominal mode)
+* AIXF032A.  Wait time: 1 minute (Switches from safe to nominal mode)
-* AIXF400A (Enables calibration accumulation)
+* AIXF400A. Wait time: a few seconds (Enables calibration accumulation)

@@ Line 1: / Line 1: @@
-If STIX has been turned off, e.g. because of an issue on the satellite, we need create a PDOR to turn it back on.
+If STIX has been turned off, e.g. because of an issue on the satellite, we need create a PDOR to turn it back on.  Previously used PDORs are available in the [https://datacenter.stix.i4ds.net/view/ior/list IOR Manager] on the STIX website.  To create one from scratch, see [[How to Write a PDOR]].
 ==Telecommands for Turning STIX On==
-Below are the telecommand sequences for turning STIX back on.  Extra things can be done as part of the PDOR, e.g. changing onboard parameters.  But this is the minimal list.
+Below are the telecommand sequences that must be included in the PDOR to turn STIX on.  Extra things can be done as part of the PDOR, e.g. changing onboard parameters.  But this is the minimal list.
 * AIXF011A (Turns STIX on and puts it into Safe mode)
 * AIXF032A (Switches from safe to nominal mode)
 * AIXF400A (Enables calibration accumulation)

@@ Line 7: / Line 7: @@
 * Set start and end time
 * Enter telecommand sequences (recommended) by clicking the Add Sequence button
- * Alternatively enter individual telecommands by clicking the Add Telecommand button
+** Alternatively enter individual telecommands by clicking the Add Telecommand button